Flow induced oscillation of two rigid rectangular plates in a side-by-side configuration

The present work is an experimental study of two oscillating rigid plates placed in side-by-side configuration, hinged at their leading edges, subjected to low subsonic flow. This problem is investigated using smoke-wire flow visualization, hot-wire anemometry, and time resolved particle image velocimetry. It is found that beyond a critical Reynolds number, the plates set into oscillatory motion. This critical Reynolds number depends on the gap between the plates. It is also seen that this value of Reynolds number, at lower values of gap to thickness ratio (<7) is significantly higher than that of the single plate configuration value. The frequency and amplitude of the oscillating plates at various gaps and Reynolds numbers have been studied and compared with the characteristics of an oscillating single plate. It is also found that depending on the gap and acceleration of the free-stream, there exist two modes of oscillation - (i) in-phase and (ii) out-of-phase. For gap to thickness ratio less than 10, only in-phase oscillations take place for all values of free-stream velocity considered in the present work, whereas, when this ratio is greater than 10, the mode of oscillation depends on the initial conditions up to a certain free-stream velocity, beyond which the plates switch to in-phase mode. Smoke wire flow visualization technique along with time resolved particle image velocimetry reveal that the vorticity distributions around the plates are responsible for the initiation of the two modes of oscillations.     

Negative compressibility property in hinging open-cell Kelvin structure

A new three-dimensional(3 D) cellular model based on hinging open-cell Kelvin structure is proposed for its negative compressibility property. It is shown that this model has adjustable compressibility and does exhibit negative compressibility for some certain conformations. And further study shows that the images of compressibility are symmetrical about the certain lines, which indicates that the mechanical properties of the model in the three axial directions are interchangeable and the model itself has a certain geometric symmetry. A comparison of the Kelvin model with its anisotropic form with the dodecahedron model shows that the Kelvin model has stronger negative compressibility property in all three directions.Therefore, a new and potential method to improve negative compressibility property can be derived by selecting the system type with lower symmetry and increasing the number of geometric parameters.     

Micromachining of circular ring microstructure by femtosecond laser pulses

In this paper, integration of interference phenomenon into femtosecond laser micromachining was reported as the femtosecond laser pulses were reshaped spatially to perform ablation. The generation of circular interference pattern was demonstrated by overlapping infrared femtosecond laser pulses. The interference pattern was subsequently focused on a copper substrate to ablate microstructures of concentric circular rings. The present technique is expected to open up new applications in the areas of rapid fabrication of micro-Fresnel lenses, hybrid microlenses and lens arrays.     

Unsteady and chaotic characteristics of natural convection field in vertical slots at large Prandtl number

In this study we examined the unsteady and chaotic characteristics of the natural convection field in vertical slots at large Prandtl number. In the computation, temperature dependence of viscosity was partially taken into consideration. As a result we discovered that the spatial region where a significant temperature fluctuation is detected corresponds to the spatial region where the secondary cells exist. The largest Lyapunov exponents calculated from the temperature on the center line have a local maximum at the lower region of the enclosure when the viscosity change was considered. These characteristics agree well with the experimental ones that have been observed by authors (Ishida, Kure and Kimoto 2001).     

Investigation of hypersonic nozzle flow uniformity using NO fluorescence

Planar laser-induced fluorescence visualisation is used to investigate nonuniformities in the flow of a hypersonic conical nozzle. Possible causes for the nonuniformity are outlined and investigated, and the problem is shown to be due to a small step at the nozzle throat. Entrainment of cold boundary layer gas is postulated as the cause of the signal nonuniformity. PACS 47.80.Jk, 47.40.Ki, 47.60.+i     

非晶态合金薄带与膜的巨磁电阻抗效应理论及计算

通过建立具有平面近横向各向异性场的非晶态合金薄带及膜的磁畴结构模型，利用线性化Maxwell方程组及Landau-Lifshitz方程，推出了在高频交变磁场及外加面内轴向直流磁场H_ex作用下的铁磁材料的与取向相关的磁导率表达式，得到了对方位角平均的相对磁导率及阻抗的计算式，导出了磁导率与张量磁化率分量间的关系，对材料磁导率的实部及虚部随H_ex的变化进行了计算，并给出了对应的磁谱图.建立的磁导率与外磁场的理论关系可将Panina及Kraus给出的理论结果统一起来. 关键词： 非晶态合金薄带及膜 取向相关磁导率 GMI效应理论与计算 近横向各向异性场     

Optimization of the surface texture for silicon carbide sliding in water

Surface texturing has been recognized as an effective means to improve the tribological performances of sliding surfaces. Usually, generation additional hydrodynamic pressure to increase the load carrying capacity is regarded as the most significant effect of surface texture. In the case of silicon carbide sliding against identical material in water, the experimental results indicate that surface texture is also helpful to improve the running-in progress to smooth the contact surfaces, showing another reason to result in low friction. Based on the consideration of enhancing the generation of hydrodynamic pressure and improving running-in progress, a surface texture pattern, which was combined with large (circle, 350 μm in diameter) and small (rectangular, 40 μm in length) dimples, was designed to maximize the texture effect on the load carrying capacity of SiC surfaces sliding in water. The friction coefficient of such textured surface was evaluated and compared with that of untextured and those only with large or small dimples only. The friction reduction mechanisms of the patterns with different dimples in size are discussed.     

Application of rainbow schlieren deflectometry to measure temperature and oxygen concentration in a laminar gas-jet diffusion flame

The quantitative rainbow schlieren deflectometry (RSD) technique was applied to measure temperature and oxygen concentration in an axisymmetric hydrogen gas-jet diffusion flame burning in quiescent air at fuel jet exit Reynolds number of 70. Schlieren measurements were compared with conventional measurements using a thermocouple and a gas-sampling probe. Good agreement between the two measurement techniques was achieved on the fuel-lean side of the flame.     

A Language for Teaching Discrete-event Simulation

Courses which teach discrete-event simulation are based on many different simulation languages. The requirements for a language to support teaching simulation are discussed. In particular, it is recommended that such languages separate into distinct modules those aspects of simulation which are taught as separate topics. Implementation of the separation is discussed. The SEESIM language, developed as a teaching aid, is described, and examples of its use are given. Straightforward use of SEESIM can be learned quickly, yet the language provides facilities for a staged introduction to advanced concepts of simulation.